| Epoxies - 2 Component
INSULCAST 136
GENERAL PURPOSE EPOXY CASTING COMPOUND
DESCRIPTION
INSULCAST 136 is an easy to use epoxy casting/potting compound exhibiting excellent adhesion to metals, ceramics and most plastics. When properly cured with INSULCURE 11B, INSULCAST 136 will conform to the requirements of MIL-I-16923, Types B, C & D, and will not support fungus growth.
| PROPERTIES-UNCURED: |
| |
Insulcast
125 |
Insulcure
9 |
Insulcure
11B |
|
| PROPERTIES UNCURED: |
| Color, visual |
Black |
Amber |
Amber |
|
| Viscosity @25°C, cps |
80,000 |
55 |
700 |
ASTM D 2393 |
| Specific Gravity |
1.59 |
.97 |
.95 |
|
| Mix Ratio (by weight) |
100 |
:6-7 |
:9-10 |
|
| Mixed viscosity @25°C, cps |
|
30,000 |
25,000 |
ASTM D 2393 |
| Pot Life (100 grams)@25°C, hrs |
|
.5 |
2.5 |
|
| Shelf Life @72°F, months |
12 |
12 |
12 |
|
| PROPERTIES-CURED: |
| PHYSICAL: |
| Hardness, Durometer (Shore D) |
|
87 |
89 |
ASTM D 2240 |
| Tensile Strength, psi |
|
10,000 |
10,200 |
ASTM D 638 |
| Tensile Elongation, % |
|
2-4 |
2-4 |
ASTM D 638 |
| Compressive Strength, psi |
|
15,000 |
15,500 |
ASTM D 695 |
| Flexural Strength, psi |
|
15,500 |
17,000 |
ASTM D 790 |
| Coefficient of Thermal Expansion, °C |
|
40 x 10-6 |
40 x 10-6 |
|
| Shrinkage on cure, in/in |
|
0.002 |
0.002 |
|
| Thermal Conductivity, BTU-in/(ft2)(hr)(°F) |
|
5 |
5 |
|
| Heat Distortion Point, °C |
|
80 |
155 |
|
| Service Temperature, °C |
|
105 |
155 |
|
| ELECTRICAL: |
| Dielectric Strength, volts/mil |
|
440 |
440 |
ASTM D 149 |
| Dielectric Constant, 1 KHz |
|
4.8 |
4.8 |
ASTM D 150 |
| Dissipation Factor, 1 KHz |
|
0.02 |
0.02 |
ASTM D 150 |
| Volume Resistivity |
|
5.0 x 1016 |
5.0 x 1016 |
ASTM D 257 |
USE INSTRUCTIONS:
1. Premix INSULCAST 136 in the original container prior to use to reincorporate any settled filler.
2. Weigh out the required amount of INSULCAST 136.
3. Measure out the appropriate amount of curing agent.
4. Mix thoroughly, scraping both sides and bottom of container.
5. Evacuate mixture at 29 in. Hg for 5-10 minutes.
6. Pour into cavity or mold.
CURING AGENT RATIO CHART:
INSULCURE 9: 6-7:100 parts INSULCURE 11B: 9-10:100 parts
CURE SCHEDULES:
Insulcure 9: 16 to 24 hours at room temperature (25°C) or, 1 hour at 65°C
Insulcure 11B: 2 hours at 100°C
Post Cure: 1 hour at 150°C
IMPORTANT:
The following supersedes any provision in your company's forms, letters and papers. AMERICAN SAFETY TECHNOLOGIES, INC. makes NO WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING WARRANTIES of MERCHANTABILITY OR of FITNESS FOR A PARTICULAR PURPOSE FOR THIS PRODUCT. No statements or recommendations contained in the product literature are to be construed as inducements to infringe any relevant patent, now or thereafter in existence. UNDER NO CIRCUMSTANCES SHALL AMERICAN SAFETY TECHNOLOGIES, INC. BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES FROM ALLEGED NEGLIGENCE, BREACH of WARRANTY, STRICT LIABILITY OR ANY OTHER THEORY, ARISING OUT of THE USE OR HANDLING of THIS PRODUCT. The sole liability of AMERICAN SAFETY TECHNOLOGIES, INC. for any claims arising out of the manufacture, use or sale of its products shall be to refund the buyer's purchase price, provided such products have been demonstrated in AMERICAN SAFETY TECHNOLOGIES, INC. sole opinion, to justify such refund.
HEALTH CAUTION:
Avoid breathing possible fumes, mists and vapors which can cause severe respiratory damage. Use of NIOSH approved breathing apparatus is required for more than minimal exposure. Always work in areas with adequate ventilation to allow dissipation of polyamine and other chemical fumes, and where applicable, solvent fumes. Use of goggles, protective garments, rubber gloves, protective cream is required. If material gets into eyes, flush thoroughly with clear water for twenty (20) minutes; then seek medical treatment. Avoid skin contact. Material can cause contact dermatitis. Always wash exposed areas immediately, using warm water and soap, followed by rinsing with clean water. Observe all safety precautions. It is important when using solvent based materials or solvents to keep away from open flame or ignition source.
PLEASE REFER TO MATERIAL SAFETY DATA SHEET FOR FURTHER FIRST AID INFORMATION.
FOR CHEMICAL EMERGENCY
CALL CHEMTREC (DAY OR NIGHT) 800 424-9300.
For Technical Bulletins Click Here...
|
