| Epoxies - 2 Component
INSULCAST 135
GENERAL PURPOSE MACHINABLE EPOXY COMPOUND
DESCRIPTION
INSULCAST 135 is a low viscosity, easily machined, general purpose potting/casting compound. INSULCAST 135 contains no fungus nutrient.
| PROPERTIES-UNCURED: |
| |
Insulcast
135 |
Insulcure
9 |
Insulcure
11B |
|
| PROPERTIES UNCURED: |
| Color, visual |
Black or Neutral |
Amber |
Amber |
|
| Viscosity @25°C, cps |
57,000 |
55 |
700 |
ASTM D 2393 |
| Specific Gravity |
1.62 |
.97 |
.95 |
|
| Mix Ratio (by weight) |
100 |
:6-7 |
:9-10 |
|
| Mixed viscosity @25°C, cps |
|
12,000 |
10,000 |
ASTM D 2393 |
| Pot Life (100 grams)@25°C |
|
30 min. |
2.5 hrs. |
|
| Shelf Life @72°F, months |
12 |
12 |
12 |
|
| PROPERTIES-CURED: |
| PHYSICAL: |
| Hardness, Durometer (Shore D) |
|
88 |
88 |
ASTM D 2240 |
| Tensile Strength, psi |
|
7,000 |
7,500 |
ASTM D 638 |
| Tensile Elongation, % |
|
2-3 |
2-3 |
ASTM D 638 |
| Compressive Strength, psi |
|
14,500 |
14,500 |
ASTM D 695 |
| Flexural Strength, psi |
|
13,000 |
13,000 |
ASTM D 790 |
| Coefficient of Thermal Expansion, °C |
|
40 x 10-6 |
40 x 10-6 |
|
| Shrinkage on cure, in/in |
|
.002 |
.002 |
|
| Heat Distortion Point, °C |
|
80 |
155 |
|
| Service Temperature, °C |
|
105 |
155 |
|
| ELECTRICAL: |
| Dielectric Strength, volts/mil |
|
440 |
440 |
ASTM D 149 |
| Dielectric Constant, 1 KHz |
|
4.6 |
4.6 |
ASTM D 150 |
| Dissipation Factor, 1 KHz |
|
0.02 |
0.02 |
ASTM D 150 |
| Volume Resistivity |
|
5.0 x 1015 |
5.0 x 1015 |
ASTM D 257 |
MIXING INSTRUCTIONS:
1. Premix INSULCAST 135 in the original container before use to ensure that any settled filler is reincorporated.
2. Weigh out required amount of INSULCAST 135.
3. Measure out required amount of curing agent.
4. Mix thoroughly, scraping both sides and bottom °F container.
5. Evacuate mixture at 29 in. Hg for 3-5 minutes.
6. Pour into cavity or mold.
CURING AGENT RATIO CHART:
INSULCURE 9 — 6-7:100 INSULCAST 135
INSULCURE 11B — 8-9:100 INSULCAST 135
INSULCURE 14 — 13-14:100 INSULCAST 135
CURE SCHEDULES:
16 to 24 hours at room temperature with INSULCURE 9, 14
2 hours @100°C plus 1 hour @125°C INSULCURE 11B.
POST CURE: - 2 hours at 155°C.
IMPORTANT:
The following supersedes any provision in your company's forms, letters and papers. AMERICAN SAFETY TECHNOLOGIES, INC. makes NO WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING WARRANTIES of MERCHANTABILITY OR of FITNESS FOR A PARTICULAR PURPOSE FOR THIS PRODUCT. No statements or recommendations contained in the product literature are to be construed as inducements to infringe any relevant patent, now or thereafter in existence. UNDER NO CIRCUMSTANCES SHALL AMERICAN SAFETY TECHNOLOGIES, INC. BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES FROM ALLEGED NEGLIGENCE, BREACH of WARRANTY, STRICT LIABILITY OR ANY OTHER THEORY, ARISING OUT of THE USE OR HANDLING of THIS PRODUCT. The sole liability of AMERICAN SAFETY TECHNOLOGIES, INC. for any claims arising out of the manufacture, use or sale of its products shall be to refund the buyer's purchase price, provided such products have been demonstrated in AMERICAN SAFETY TECHNOLOGIES, INC. sole opinion, to justify such refund.
HEALTH CAUTION:
Avoid breathing possible fumes, mists and vapors which can cause severe respiratory damage. Use of NIOSH approved breathing apparatus is required for more than minimal exposure. Always work in areas with adequate ventilation to allow dissipation of polyamine and other chemical fumes, and where applicable, solvent fumes. Use of goggles, protective garments, rubber gloves, protective cream is required. If material gets into eyes, flush thoroughly with clear water for twenty (20) minutes; then seek medical treatment. Avoid skin contact. Material can cause contact dermatitis. Always wash exposed areas immediately, using warm water and soap, followed by rinsing with clean water. Observe all safety precautions. It is important when using solvent based materials or solvents to keep away from open flame or ignition source.
PLEASE REFER TO MATERIAL SAFETY DATA SHEET FOR FURTHER FIRST AID INFORMATION.
FOR CHEMICAL EMERGENCY
CALL CHEMTREC (DAY OR NIGHT) 800 424-9300.
For Technical Bulletins Click Here...
|
